The show 23 switch

Experience, with cartoon-style graphics and accessible gameplay. RBI Baseball 19 is another option, featuring realistic visuals and an authentic MLB experience. If you're looking for a more retro experience, then check out Super Baseball 2020, an SNES-style title with 8-bit graphics and classic gameplay. Finally, Retro Baseball, also available on the Switch, is a classic-style game that features polygonal graphics and an arcade-style playing experience.Will MLB The Show 23 be on switch?At this time, there is no official confirmation as to whether or not MLB The Show 23 will be released on the Nintendo Switch. While there has been speculation and rumors, Sony has not released any official statement on the matter. Therefore, until Sony makes an official announcement, it is impossible to definitively answer this question. That being said, given the success of MLB The Show 21 on the Nintendo Switch, it is possible that Sony could decide to release a version of the game on the Switch in the future.

[no] ptp sync interval log-seconds Example: switch(config-if)# ptp sync interval 1 (Optional) Configures the interval between PTP synchronization messages on an interface. The range is from log(–3) to log(1) seconds. For the media-related profile information, see the Cisco NX-OS IP Fabric for Medial Solution Guide when configuring PTP for media. Step 19 (Optional) [no] ptp sync interval [aes67-2015 | smpte-2059-2] log-seconds Example: switch(config-if)# ptp sync interval aes67 1 (Optional) Configures the interval between PTP synchronization messages on an interface. Table 4. PTP Synchronization Interval Range and Default Values Option Range Default Value aes67-2015 –4 to 1 log seconds –2 log seconds smpte-2059-2 –4 to –1 log seconds –2 log seconds Without the aes67-2015 or smpte-2059-2 option –3 to 1 log seconds –2 log seconds Step 20 (Optional) [no] ptp vlan vlan-id Example: switch(config-if)# ptp vlan 1 (Optional) Specifies the VLAN for the interface where PTP is being enabled. You can only enable PTP on one VLAN on an interface. The range is from 1 to 4094. Step 21 (Optional) ptp destination-mac non-forwardable rx-no-match accept Example: switch(config-if)# ptp destination-mac non-forwardable rx-no-match acceptswitch(config-if)# (Optional) Accepts and responds to nonforwardable destination MAC address packets. These destination MAC addresses are used in the PTP messages that are exchanged between the GM clock, PTP-master clock, and PTP-slave clocks. This command is supported beginning with Cisco NX-OS Release 9.3(5) and only on the Cisco Nexus 93180YC-FX3S switch. Step 22 (Optional) show ptp brief Example: switch(config-if)# show ptp brief (Optional) Displays the PTP status. Step 23 (Optional) show ptp port interface interface slot/port Example: switch(config-if)# show ptp port interface ethernet 2/1 (Optional) Displays the status of the PTP port. Step 24 (Optional) copy running-config startup-config Example: switch(config-if)# copy running-config startup-config (Optional) Copies the running configuration to the startup configuration. Configuring PTP in Unicast Mode Configuring Unicast Mode

2020Hardware frequency correction : NAPTP Clock state : Free-Run show ptp brief The output of this command displays the PTP clock state for each configured port. The following is an example of the output of the show ptp brief command: switch# show ptp briefPTP port status-----------------------------------Port State--------------------- ------------Eth1/1 SlaveEth1/6 DisabledEth1/7 DisabledEth1/8 DisabledEth1/10 MasterEth1/11 DisabledEth1/12 DisabledEth1/13 MasterEth1/14 DisabledEth1/15 DisabledEth1/16 DisabledEth1/17 DisabledEth1/18 DisabledEth1/19 DisabledEth1/20 DisabledEth1/21 DisabledEth1/22 DisabledEth1/23 DisabledEth1/24 DisabledEth1/25 DisabledEth1/26 DisabledEth1/27 DisabledEth1/28 DisabledEth1/29 DisabledEth1/30 DisabledEth1/31 DisabledEth1/32 DisabledEth1/33 DisabledEth1/34 DisabledEth1/35 DisabledEth1/36 DisabledEth1/37 DisabledEth1/38 DisabledEth1/39 DisabledEth1/40 Disabled show ptp clock foreign-masters record The output of this command displays the state of foreign masters known to the PTP process. For each foreign master, the output displays the clock identity, basic clock properties, and whether the clock is being used as a grandmaster.. The following is an example of the output of the show ptp clock foreign-master-record command: switch# show ptp port statusP1=Priority1, P2=Priority2, C=Class, A=Accuracy,OSLV=Offset-Scaled-Log-Variance, SR=Steps-RemovedGM=Is grandmaster--------- ----------------------- --- ---- ---- --- ----- --------Interface Clock-ID P1 P2 C A OSLV SR --------- ----------------------- --- ---- ---- --- ----- --------Eth1/1 00:00:00:00:00:00:00:01 128 128 6 33 65535 0 GM Configuration Examples for PTP This example shows how to configure PTP globally on the device, specify the source IP address for PTP communications, and configure a preference level for the clock: switch# configure terminalswitch(config)# feature ptpswitch(config)# ptp source 10.10.10.1switch(config)# ptp priority1 1switch(config)# ptp priority2 1switch(config)# show ptp briefPTP port status-----------------------Port State------- --------------switch(config)# show ptp clockPTP Device Type: Boundary clockClock Identity : 0:22:55:ff:ff:79:a4:c1Clock Domain: 0Number of PTP ports: 0Priority1 : 1Priority2 : 1Clock Quality: Class : 248 Accuracy : 254 Offset (log variance) : 65535Offset From Master : 0Mean Path Delay : 0Steps removed : 0Local clock time:Mon Dec 22 14:13:24 2014 This example shows how to configure PTP on an interface and configure the intervals for the announce,